Metal shutter Mours (95260)

Mours (95260)

Your metal shutter expert in Mours

DRM Paris is the metal shutter specialist in Mours (95260) and across the Val-d'Oise (95) department. Emergencies at any hour, made-to-measure installation, motorisation or simple servicing: the same method applies everywhere — free quote, public prices and guaranteed work, in Mours as throughout Île-de-France.

Shopkeepers, homeowners, managing agents and businesses in Mours: the quote is free, the amount is confirmed before any work and the invoice meets insurers' requirements. See the full price list on our metal shutter page, or call 07 66 54 96 41 directly.

24/7 emergency release
All-fault repair
Motor & motorisation
Shutter locks

Transparent prices

Metal shutter prices in Mours (95260)

Service	Price
Metal shutter call-out (travel + diagnosis + minor repair)	From 150 €
Jammed shutter release	From 180 €
Shutter lock repair	From 200 €
Shutter axle repair	From 200 €
Electrical system servicing	From 200 €

See the full price list

Photos of our work

Our metal shutter work near Mours

New galvanised solid-slat shutter with housing fitted on an access door – repair in Mours — New fitting with housing

Closed micro-perforated shutter protecting a medical centre entrance – repair in Mours — Micro-perforated in a mall

Galvanised wave grilles ready to fit, made in our workshop – repair in Mours — Wave grilles ready to fit

24/7 repair & call-out

Metal shutter repair in Mours: every fault covered

In Mours, most metal shutter call-outs involve the same components: the curtain and its slats, the winding shaft and springs, the lock and the motor. Our technician identifies the exact cause — not just the symptom — before any repair.

Mechanical faults

Bent, cracked or dislodged slats to replace
Seized, warped or noisy winding shaft
Broken compensation spring, worn spring boxes
Damaged guide rails after an impact
Jammed shutter lock or forced cylinder after a break-in
Curtain off its tracks or twisted side guides

Electrical & motor faults

Failing safety edge or sensors
Tubular or central motor failure
Dead remote control, blown fuse, power cut
Shutter that only lifts halfway or moves in jerks
Faulty key switch or control box
Misadjusted limit switches: the shutter no longer stops

Shutters and grilles we service

Solid-slat metal shutter (galvanised steel or aluminium)
Extensible grille and corrugated-tube curtain
Micro-perforated slats for shop windows
Straight-tube jeweller's grille, high security
Projection shutters and car-park closures
Manual (push-up) or motorised metal shutter

We repair, replace and motorise every brand of shutter motor: Somfy, Simu, Nice, Becker, Came, Gaposa and generic drives. We also offer preventive maintenance in Mours — greasing the guides, adjusting limit switches, checking the springs — to extend the life of your installation.

Frequently asked questions – metal shutter Mours

How fast can you reach Mours?

We answer 24/7 on 07 66 54 96 41. For a jammed metal shutter in Mours, a local technician is typically on site within 30 minutes to 1 hour depending on traffic. Securing your shop or premises always comes first.

Metal shutter stuck in Mours: what should I do while waiting?

Never force a jammed shutter: you risk bending slats, warping the shaft or burning out the motor, making the repair more expensive. Cut power to the motor, leave the lock alone and call us — we'll give you the right steps until the technician arrives.

How much does a metal shutter repair cost in Mours (95260)?

Repairs start at €150 and emergency release at €180, travel and diagnosis included. The exact price is announced over the phone and confirmed by a free quote before any work — our rates are identical across Île-de-France, with no surcharge for Mours.